919325132311 919325132311
Bajaj Steel Industries Limited

Ginning & Pressing

  • 2000 Extractor Saw Gin

    Feeder Motor (not Included with Machlne)….15 Hp, 1800 Rpm (60 Cycle) : 15 Hp, 1500 Rpm (50 Cycle) or No Motor Used When Driven from the Gin Saw Shaft

    Feed Roller Motor : 3/4 HP, 1800 RPM, 230/460 Volt, 3-phase 60Hz TEFC Frame, 56C (wire for 230 volt)

    Four Spiked Cylinders : 11” Diameter (279.4 Mm)

    Two Channel Saw Cylinders : 16-1/2” Diameter (419.1 Mm)

    One Saw Dotter Cylinder : 11-5/8” Diameter (295.2 Mm)

  • Model 9000 Extractor

    Extractor-feeder Motor : 15 Hp, 1800 Rpm or from Gin (not Included with Machine) Saw Shaft

    Feed Motor : 3/4 HP, 1800 RPM, 230/460 volt, 3-phase 60 Hz, TEFC Frame 56C (wire for 230 volt)

    Gear Reducer : Grant, 30:1 Ratio, Stf 225 Worm Gear W/standard Length Shaft

    Four Saw Cylinders : 16 1/2″ Od, 95 5/8 Long, 160 Saws 5/8″ Wide

    Two Doffing Cylinders : 11 5/8″ Od, 95 5/8″ Long

  • Model 9120 Extractor

    Extractor/feeder Motor : (not Included with Machine) 25 Hp, or from Saw Shaft

    Feed Motor : 3/4 HP

    Gear Reducer : 30:1 Ratio

    Four Saw Cylinders : 16″ ½” 00 (419.1mm),119 1/2” long (3035mm)

    Two Doffing Cylinders : 11 5/8″ (295.3mm) 00, 119 1/2″ long (3035mm)

  • Model 9300 Up-Packing Press

    Press (Complete)Weight : 89,300 lbs. (40506 Kgs.)

    Upper Beam Weight : 11,060 lbs. (5016 Kgs.)

    Lower Beam Weight : 15,900 lbs. (7211 Kgs.

    Upper Ram Weight : 2,900 lbs. (1315 Kgs.)

    Lower Ram Weight : 9,900 lbs. (4490 Kgs.)

  • Model 9500 Down-Packing Press

    Universal Density : 20”X54” (.508m X 1.3716m)

    High Density : 20” X 41” (.508m X 1.0414m)

  • Centrifugal Lint Cleaner

    Discharge Vaccum : 2 in. (51 mm) WGNEG Air

    Velocity : 12,000 Ft./min. (3658 M/min)

    Mote Opening : Variable, Set 1 Inch (25.4 Mm) At Factory

    Length Inside : 96 in. (2438 mm)

    Overall : 120 in. (3048 mm)

  • Impact Cleaner

    Features :

    • Heavy Steel Construction
    • Sealed Bearings Throughout
    • Spiked Drums on full length shafts
    • Brush Doffer
    • Serrated Discs made of Saw Steel
    • Positive serpentine
  • Suction Command Seed Cotton Feeding System

    The Suction –Command System takes the worry out of finding dependable labour for suction feeding seed cotton from your trailers or modules. The standard system consists of two lanes independent suction lanes. Bajaj’s Suction –

  • Cotton Module Feeding System

    The Bajaj Module Feeder controls the volume of seed cotton conveyed dispersed and fed into the gin and is limited only by the maximum seed cotton feeding capacity of the gin machinery.

     

    The dual drive system allows modules to

  • Super III Stick Machine

    Shown with 24” vacuum – Vacuum, ductwork, and supports are not included with the Super III

     

    The Super III is unequalled for bulk removal of sticks, hulls and leaves from machine picked or stripped cotton. Cotton

  • Vertical Flow Drier

    The bajaj-cec vertical flow driertm dries better by doing the right thing at the right time. every ginner knows that cotton can’t be cleaned until it is dried and it cant be dried until it is loosened and fluffed so that hot air can

  • Stone Remover Cum Hot Box

    Capacity / hour (Avg) : 10,000 Kgs

    Feeding System : Belt Conveyor

    Height : 1220 mm

    Width : 1015 mm

    Length : 1150 mm


«« Previous Pages: 1   2   3   4   Next »

Contact Us

Bajaj Steel Industries Limited

C-108, Midc Industrial Area, Hingna, Nagpur - 440028, Maharashtra, India

Mr. Lalit Kalantri General Manager Sales ( For Sales Enquiry / Existing Clients only)

Email : kalantri@bajajngp.com

Mobile : +91-9325132311

Mr. Nilesh Laddhad,GM Project and Purchase (For Purchase Enquiry only)

Email. : nladdhad@bajajngp.com

Mobile. : +91-7030953049

Phone : +91-07104-238101

Mrs. Suneet Menon, Senior Manager HR & IR (For HR & IR related only)

Mobile.. : +91-7104238101-20

Emails, : menon.suneet@bajajngp.com



Looking for Product Name ?